High front gutter roll forming machine

-
High front gutters hide the lower edge of tiles or roof cladding which creates an aesthetically pleasing appearance. It is important that sufficient overflow measures are included in the design of the guttering system and that high fronted gutters are installed in such a way that if they overflow, it will not result in water flowing back into the roof or building.

The design of gutter and downpipe system installations also need to comply with specific rainfall intensities for the area of installation and adequate overflow provisions need to be provided to prevent water from entering the dwelling during heavy rainfall periods.
Here is some sizes of high front gutter


There are two natural effects in our guttering that offer some protection against water flowing from eaves gutters inside a building, when attached to steel fascia. 
(1)The first is that when installed on our steel fascia, the "high front" of the gutter can still be lower than the top face of the fascia. Water will always flow to the lowest point, and even if a complete blockage exists, should still overflow outside the eaves line.
(2)Secondly, if a complete blockage occurs the additional weight of the water will cause the gutter to temporarily deform. The back of the gutter is restrained at 1.2 metre intervals by fixing clips but between these points the gutter moves outwards from the fascia creating a gap that allows the additional water to escape.

Here is a picture of high front gutter roll forming machine

Parameters of high front gutter roll forming machine:

1
feeding material
color steel coil, aluminum,GI,PPGI
2
material thickness
0.2~1mm
3
material yield stress
230~550mpa
4
feeding width
as per need
5
forming speed
8~25m/min
6
cutter material
cr12
7
roller material
45# steel with chrome treatment 
8
Cr plating thickness
0.05mm
9
roller station
11 pieces(according to different profiles)
10
controller
 PLC , touch screen and button
11
hydraulic station motor power
3kw
12
hydraulic presure
12mpa
13
main motor power
7~8.5kw
14
voltage
380v 3ph 50hz / as your needs
15
total weight
6~8t
16
dimension
10 x 1.5 x 1.5m

Maintenance of the high front gutter

Water will overflow to the front of the gutter if the top of the front gutter bead is located below the top of the fascia. Due to the gutter fall, this may occur towards the end of a gutter run in which case the portion of gutter beginning 5mm below the top of the fascia may be used in the overflow calculations. 
The perfect solution to create a consistent gap between the gutter and fascia, llowing water to escape through the gap rather than entering the building. The clip facilitates the required 10mm minimum distance between the top of the fascia and the back of the gutter and is available to suit Contour and Clickfast steel fascias as well as timber fascia.  

If you want to know more detail data about this roll forming machine, please feel free to contact with us at any time.
Email: roofingmachine@zhongtuocn.com
Whatsapp: +8615127755788 and +8613733275488

Comments

Post a Comment

Popular posts from this blog

Solid Steel Shutter Machine of Rolling Forming for UK-Mode ZTAC11

-
Image
Solid Steel Shutter Machine of Rolling Forming for UK-Mode ZTAC11 is specailly designed for the UK market. Steel shutters are used to help prevent unauthorized access and vandalism to premises by adding an extra barrier between "outside" and whatever entrances they may be protecting. When open, the shutters provide an almost unobstructed aperture as the shutter and mechanism store above the doorway and out of the way. Furthermore, the doors are tough and have a long life with little maintenance required.  For the UK-Mode ZTAC11 drawing profile here for your reference:   For the Solid Steel Shutter matched elements like U channel guardrail, and the bottom slat, we also can make for you; in next ariticle I will share more information. Here mainly for the Solid Steel Shutter Machine of Rolling Forming for UK-Mode ZTAC11: Solid Steel Shutter Machine Introduction: 1.Gcr12 Mov roller material, equal to SKD11. Very hard, long time to use.  2.Hydraulic shearing with the ser
Read more

Slotted angle rolling forming machine

-
Image
Slotted angle machine allows you to make the slotted angle in batch by rolling forming principle. Slotted angle (also sometimes referred to as slotted angle iron) is a system of reusable metal strips used to construct shelving, frames, work benches, equipment stands and other structures. The name derives, first, from the use of elongated slots punched into the metal at uniform intervals to enable assembly of structures fixed with nuts and bolts, and second, from the longitudinal folding of the metal strips to form a right angle. Here are some drawing profile and finished product pictures for your reference: Sample in real: Slotted angle rolling forming machine design: The machine is composed by the following elements: Slotted angle usage: To construct items from slotted angle, items can be cut to size (some versions are marked to show the optimum points at which to cut the metal) using special slotted angle cutters or shears, and then fixed with nuts and bolts. Tension
Read more

Metal coil door frame roll forming machine

-
Image
Metal coil door frame roll forming machine Steel door frame machine is a good choice for strength and durability, the finished product of this machine is of the highest quality and high strength, offering a high level of security, These are some drawing profiles and finished production pictures: Hydraulic Punching hole, angle & forming in one production line with Computer Control System. Spot welding free, each corner has been pre-cut with a 45 mitre, giving a accurate fit There is a simple of drawing profiles for your reference: Here is one picture of finished product: According to this information, we advice you a machine as following: main parameters of this machine: 1) Machine frame: middle plate frame 2) roller material: GCr15MoV quenching treatment 58-60° 3) Main motor power: 11kw. 4) Hydraulic power: 4KW. 3) Voltage: 380v,50Hz,3 phase 4) Cutting blade: Cr12mov quenching treatment 58-62°. 5) Cutting tolerance: +/- 1.0mm, 45degree cutting system. 6) Drive: Chain
Read more